We're Your Source of Genuine Quatro Air Filters and Parts 
HEPA Filters, Bag Filters, Dust Pre-Filters, Chemical Odor Filters, Bulk Chemical Media, Motors, UV Light, etc.

We Make Clean Air - Air Purifiers That Truly Clean
air purifiers, fume extractors, dust collectors, dust, chemical odor removal 
Shipped direct to you factory fresh , North America Toll Free 1-800-626-0664

SPH426 laser fume extractor

Laser Marking, Engraving, Cutting - captures laser smoke and fumes at source using small diameter tip extraction, high pressure blower / motor, 8" deep bed chemical gas odor filter 

Laser Engraving, Laser Marking, Laser Cutting - Fume and Smoke Extractor - Standalone Filtered Exhaust

The SPH426 Fume Extractor by Quatro Air is a self contained unit, that connects to the laser engraver via flexible heavy duty grounded hose that is provided.

STANDALONE FILTERED EXHAUST

This is a self contained unit, that connects to the laser engraver via flexible heavy duty grounded hose that is provided. The inlet diameter can accommodate a 2", 3" or 4" collar hose connection.

Discharge is recirculated back into the room via vents at the bottom of the system. However, there is an optional side collar adapter kit to allow venting to the exterior if required. The unit is very quiet, and takes up very little floor space (approx. 1.25 sq. ft.) At 30 inches high the unit is ideal to be tucked under a table. This can save precious floor space. If required, the entire system is easily relocated via industrial grade casters on the bottom of the exhaust unit. All the filter elements can be replaced without the need for tools in very short order. The inexpensive filters make this an economical solution for most end users.  

Installation - Easily Assembled, requires no tools

This unit is easily assembled, requires no tools, no need for a technician. The deep bed chemical filter allows for maximum VOC removal.  The chemical filter is lowered in from the top lid. The 99.97% HEPA filter guarantees the removal of particles as small as 0.3 microns in diameter.

More About the SPH426 Laser Fume Extractor Nice To Know

The SPH400 Fume Extractor and Air Filtration System is designed with up to 4 stages of filtration each targeted for removal of specific size particles and gases. 

There are a series of filters in the system to ensure that all particulate matter/ dust is removed efficiently:
 
Particulate Filtration:
The unit contains multi-layer knock out pad filters, Deep Pleated high capacity safety filters and a MERV 17 99.97 % HEPA filter.    
The HEPA filter is the last particulate filter in the sequence and it is designed to remove 99.97% of all particulate matter that is 0.3 microns and larger.    
This is the same type of filter that is used in hospital operating rooms. 
Please note as the filters begin to get dirty they also become more efficient making the system more efficient as time goes on. 
This occurs as it gets more and more difficult for the dust to pass through the filter due to the passages becoming smaller as they become filled with debris.    

Gas Phase Chemical Fume Odor Filtration:
The gas phase filter is quite large and 8” deep in direction of airflow. 
We have 26 different types of chemical media that can be incorporated into the chemical filter to address and deal with specific contaminants if required.    
Depending on the type of media the modules could weigh as much as 40 lbs.    
Our standard and most typical module contains a virgin bituminous coal extruded 3-4 mm carbon pellet.    
This carbon is ideal at removing many VOC’s and has a holding capacity as high as 25 % by weight. Initially the removal efficiency will be 100% for most VOC’s. Over time the mass transfer zone will travel through the chemical filter as it gets consumed.    
The chemical filter is seated inside a gel seal material to guarantee zero by-pass of the chemical filter. This is the same material that is used in Pharmaceutical and Hospital environment clean rooms. All gases therefore must pass through the chemical filter.     
Unlike other systems that have a sprinkling of carbon our gas phase chemical filter is quite large and requires the use of high pressure blowers to overcome the resistance created by the deep bed chemical filter. 

Our blowers are capable of generating 90” water column of pressure. With this type of blower as the filters begin to get dirty and plugged we can still effectively overcome this increase in pressure. 

The system is equipped to advise you when the filters need to be changed.  

|Filter Sequences Available / Specs Dual Infinity Motors|Filter Sequences / Specs - Brushless Motor|SPH426 Laser Fume Extractor PDF|

Replacement Filters for the SPH426 Fume Extractor

Genuine Quatro Air Replacement Filters

Request Quote - Info - Call 1-800-626-0664 to order